This new installation is needed if you want to use Reason or other Propellerhead software in compliance with the ReWire and Rex specifications. 15:40 This update installs the ReWire and Rex shared libraries in the way Windows Vista expects them to be installed. Noteman says: Visit Propellerhead's website for more information on ReWire. ReWire allows you to stream Finale's audio output to a 3rd party digital audio workstation (DAW). Finale acts as an audio device and your DAW is a host. Check with your DAW's manufacturer to see if ReWire is supported. Is by far one of the most powerful little plug-ins in the arsenal!assuming that you're using both Akai's software. /Library/Application Support/Propellerhead Software/ReWire/Mixup ReWire Device.bundle Note: the 2 paths above are located at the root of your drive (/Library) and NOT FROM YOUR USER FOLDER (/Library or /Users//Library).
Messages
| bang | In left inlet: If a ReWire device has been loaded, bang causes a list of its output channel names to be sent out the second-from-right outlet. | |
| int | transport-start/stop-flag (0 or 1) [int] | In left inlet: 1 starts the ReWire transport, 0 stops it. No sound can occur without the transport being started. |
| anything | rewire-device-name [list] | In left inlet: The symbol is interpreted as the name of a ReWire device. If the name is valid, rewire~ attempts to switch to the device. |
| closepanel | In left inlet: Closes the current device's user interface panel if it is open. | |
| device | device-index [int] | In left inlet: The word device, followed by a number, switches to the ReWire device associated with the number index. The index is obtained as the order in which device names appear in a pop-up menu object connected to the second-to-right outlet. |
| loadbang | Same as bang but the action is performed upon loading the patch within which the rewire~ object is performed. | |
| loop | start-point (samples) [int] end-point (samples) [int] loop-flag (0 or 1) [int] | In left inlet: The word loop, followed by three numbers, sets the current loop position and mode. The first number sets the loop start position in samples. The second number sets the loop end position in samples. If the third number is 1, looping is turned on. If the third number is 0, looping is turned off. However, note that ReWire clients may ignore looping if they do not produce transport- or time-based output. For example, a software synthesizer that only responds to MIDI note commands would probably not be affected by looping. |
| map | device-output-channel and object-outlet [list] | The word map, followed by two numbers, maps a ReWire device's output channel to an outlet of the rewire~ object. ReWire channels start at 1 with a maximum of 256. rewire~ object outlets are specified starting at 1 for the left outlet, or 0 to turn the ReWire channel off. For example, map 3 2 causes the ReWire device's audio output channel 3 to be mapped to the second-from-left outlet of the rewire~ object. You can find out the names of the ReWire audio output channels with the bang message after the rewire~ object has a connection to a ReWire device. By default, audio outlets map to the first channels of the ReWire device; in other words, the leftmost signal outlet outputs the first channel of the device. |
| midi | time-stamp MIDI-bus-index MIDI-message-status-byte and MIDI-message-data-bytes [list] | In left inlet: The word midi, followed by four or five numbers, sends a MIDI event to a ReWire device. The first number is a time stamp value and is currently ignored (in other words, the event is sent out immediately). The second number is the MIDI bus index. ReWire 2 has 256 MIDI busses, indexed from 0 to 255. The third number is the MIDI message status byte, and the fourth and fifth numbers are the MIDI message data bytes. |
| openpanel | In left inlet: If the current device has a user interface panel, the word openpanel will open it. | |
| play | In left inlet: Starts the ReWire transport. | |
| position | play-position (samples) [int] | In left inlet: The word position, followed by a number, sets the current play position (in samples). |
| stop | In left inlet: Stops the ReWire transport. | |
| tempo | beats-per-minute [float] | In left inlet: The word tempo, followed by a number, sets the tempo to that number in beats per minute. ReWire handles integer or floating-point valude for tempos, and tempo is updated on the next call to the client to return audio samples. |
This update installs the ReWire and Rex shared libraries in the way Windows Vista expects them to be installed. Please note the following:
* Only run this installer if you are running Windows Vista. This installer is not for Windows XP or any other version of Windows.
* Run this installer last, meaning after you have installed Reason and all other ReWire applications.
* If you install or reinstall a ReWire application on your system, you will need to run this installer again.
It is highly recommended to always use the most recent driver version available.
Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.
Rewire Propellerhead Download
Propellerhead Rewire 64-bit
- COMPATIBLE WITH:
- Windows Vista
- file size:
- 468 KB
- filename:
- Install_ReWire_&_Rex_for_WindowsVista.zip
- CATEGORY:
- Other Drivers & Tools